Stainless Steel Precision Shaft Quality (PSQ) Bars

Precision shaft quality stainless steel bar, 8 mm to 81 mm, straight to 0.015 inch TIR per 10 feet

Stainless steel precision shaft quality bars produced by Laxcon Steels

Product Description

Precision shaft quality (PSQ) bar is a supply condition, not a grade: a ground and polished round bar held to a shaft fit and a straightness limit so that it runs in bearings and seals without further machining. Laxcon Steels supplies PSQ bar from 8 mm to 81 mm in lengths up to 6.4 metres, to h7, h8, h9, j6, f7 or f8, with straightness of 0.015 inch total indicator reading per 10 feet. Every bar is checked for ultrasonic flaws, and eddy current testing is carried out where the order calls for it.

The bar is used for pump shafts, cylinder shafts, boat shafts, piston shafts, valve shafts and bearing bars. The standard supply is rated at 75 ksi tensile strength, and 304 stainless steel shafting at 100 ksi tensile strength is available. Heat treatment is supplied as soft annealing, solution annealing, and quench and temper. Bars are packed with distance rings in plywood boxes so that the straightness survives transit. Bar without the fit and straightness requirement is bright bar, which the same lines finish from 5 mm to 115 mm.

Weight per metre by diameter is in the round bar weight chart. How shaft material is classified and selected is covered in the stainless steel shafts manual.

PSQ Bar Specifications

Size range
8 mm - 81 mm (5/16" - 3-3/16")
Length
Up to 6.4 metres
Tolerance
Diameter limits h7, h8, h9; shaft fits j6, f7, f8
Straightness
0.015” TIR (total indicator reading) per 10 ft.
Heat treatments
Soft Annealing, Solution Annealing, Quench & Tempered
Contamination
Free from radioactive elements, mercury and lead
Testing
PMI grade check with handheld spectrometers
Inspection
Eddy current testing on request
Production
Made to order in every grade listed on this page
Certifications
IATF 16949:2016, AS9100:2016 Rev. D, CE Marking

Sizes and Tolerances

Tolerance by size, ISO 286

Nominal diameter (mm)h7h8h9
over 6 to 100 / -0.0150 / -0.0220 / -0.036
over 10 to 180 / -0.0180 / -0.0270 / -0.043
over 18 to 300 / -0.0210 / -0.0330 / -0.052
over 30 to 500 / -0.0250 / -0.0390 / -0.062
over 50 to 800 / -0.0300 / -0.0460 / -0.074
over 80 to 1200 / -0.0350 / -0.0540 / -0.087

Deviations in millimetres from the nominal size, ISO 286-1 and ISO 286-2.

The j6, f7 and f8 fits

A pump shaft runs inside a bearing, a sleeve or a seal, and the drawing therefore calls for a fit rather than a plain tolerance. Under ISO 286 the j6 class straddles nominal size by a few micrometres either way, and the f7 and f8 classes sit wholly below nominal with a clearance that grows with diameter. Laxcon grinds precision shaft quality bar to those classes to order; the h7 to h9 columns above are the plain classes supplied when the customer finishes the journals.

Straightness is held to 0.015 inch total indicator reading per 10 feet (0.38 mm over 3.05 m), which is the figure the pump industry specifies for shafting, and the bar is supplied in the annealed condition at a minimum yield of 75 ksi (517 MPa) for the 300 series shaft grades, with quench and tempered martensitic and precipitation hardening grades available where a higher strength is required.

Weight per metre

Diameter (mm)kg per metreMetres per tonne
80.402,518.3
100.621,611.7
120.891,119.2
161.59629.6
202.48402.9
253.88257.9
305.58179.1
357.60131.6
409.93100.7
4512.5679.6
5015.5164.5
6022.3444.8
7030.4032.9
8140.7124.6

Density 7.90 g/cm³ (π/4 x d² x 0.0079). A 304 bar at 7.93 g/cm³ runs 0.4 percent heavier, a 316 bar at 7.98 g/cm³ 1 percent heavier. Sizes are the published range at the nominal diameters shown.

PSQ Bar Reference

Governing standards

EN 10088-3
Stainless steels: technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products for general purposes. Composition, heat treatment condition and mechanical properties per grade.
EN 10278
Dimensions and tolerances of bright steel products: the h and k tolerance classes for drawn, turned, peeled and ground bars.
ASTM A276/A276M
Stainless steel bars and shapes: composition, condition, mechanical properties and finish designations for hot-finished and cold-finished bar.
ASTM A484/A484M
General requirements for stainless steel bars, billets and forgings: permissible variations in dimensions, straightness, weight and length, and the test and marking requirements every bar order inherits.
ISO 286-1 and 286-2
The ISO code system for tolerances on linear sizes: the IT grades and the fundamental deviations behind h7, h9, h11, k12, k13, j6, f7 and f8.
EN 10204
Metallic products, types of inspection documents: the 2.2 test report and the 3.1 and 3.2 inspection certificates a purchase order can call for.

Precision shaft quality bar against bright bar

A bright bar is finished to a diameter class and a surface roughness. A precision shaft quality bar is finished to a fit, a straightness and a stated minimum yield, because it will rotate in service and the runout that a general-purpose bright bar tolerates would show as vibration in a pump or a marine drive. The two share the finishing routes and the size overlap from 8 to 81 mm; the difference is what is measured before the bar leaves the works.

The stainless steel shaft manual sets out which grade suits which service and the PSQ bar article explains the pump shaft quality designation itself.

Frequently Asked Questions

What PSQ bar sizes does Laxcon make?

Laxcon makes precision shaft quality bars from 8 mm to 81 mm diameter, in lengths up to 6.4 metres.

Which PSQ tolerances and straightness are available?

Precision shaft quality bars can be supplied to h7, h8, h9, j6, f7 or f8 tolerances. Straightness is held to 0.015 inch TIR per 10 feet.

How are pump shaft quality bars inspected?

Every precision shaft quality bar is checked for ultrasonic flaws, eddy current testing is carried out where the order calls for it, and positive material identification with a handheld spectrometer confirms the grade.

How can precision shaft quality bars be packed and traced?

Laxcon packs precision shaft quality bars in standard bundles of 500 to 1,000 kg with HDPE or LDPE wrapping and two lifting slings. ISPM 15 wooden boxes and fibre-tube packing are available, and every bundle is marked with heat number, grade, size, and net and gross weight.

What is the weight of a 25 mm PSQ bar per metre?

A 25 mm precision shaft quality bar weighs 3.88 kg per metre at 7.90 g/cm³, so one tonne holds about 258 metres. Weight per metre is the diameter in millimetres squared times 0.006205, and a 316 bar runs 1 percent heavier.

Which grades are PSQ bars made in?

PSQ bar is supplied in the 300 series austenitic shaft grades such as 304 and 316, and in quench and tempered martensitic and precipitation hardening grades where a higher strength is required. 304 shafting at 100 ksi tensile strength is available.

Is PSQ bar heat treated?

PSQ bar is supplied soft annealed, solution annealed, or quenched and tempered. The austenitic grades cannot be hardened by heat treatment and gain strength from cold work in the drawing and finishing route.

What is the price of a stainless steel PSQ bar?

Stainless steel PSQ bar is priced per kilogram, and the price depends on the grade, the size, the tolerance class, the finish, the length and the quantity ordered. Laxcon Steels quotes each order on request; what moves the price of stainless steel in general is set out in the stainless steel price article.

More questions

What does h7 tolerance mean on a 25 mm PSQ bar?

Under ISO 286, h7 allows a 25 mm bar to measure 24.979 to 25.000 mm, never oversize. h8 allows 24.967 to 25.000 mm and h9 allows 24.948 to 25.000 mm. The tolerance table above gives each class for every size band.

What do the j6, f7 and f8 fits mean on a shaft bar?

Under ISO 286, j6 straddles the nominal size by a few micrometres either way. The f7 and f8 classes sit wholly below nominal, with a clearance that grows with diameter, so the shaft runs freely in a bearing, sleeve or seal. Laxcon grinds PSQ bar to these classes to order.

What is the straightness of a PSQ bar in millimetres?

A straightness of 0.015 inch total indicator reading per 10 feet equals 0.38 mm over 3.05 metres. Bars are packed with distance rings in plywood boxes so that the straightness survives transit.

What are PSQ bars used for?

PSQ bar is used for pump shafts, cylinder shafts, boat shafts, piston shafts, valve shafts and bearing bars. The fit and straightness let the bar run in bearings and seals without further machining.

How does Laxcon make PSQ bars?

Laxcon melts and rolls the steel into round bar in its own plants, then grinds and polishes it to a shaft fit and straightness on the same lines that finish its bright bar. Every bar is checked for ultrasonic flaws before it leaves the plant.

Which grades are used for shafts?

The shaft material follows the service fluid and the load, with 304 and 316 for corrosive duty and 431 or 420 for load and wear, and the stainless steel shafts manual sets out the choice in full.

CATALOGUE

More
Products