Stainless Steel Square Bright Bars
Cold drawn stainless steel square bar, 12.7 mm to 55 mm, held to h11, k12 and k13
Product Description
Stainless steel square bright bar is square bar cold drawn to size, with a bright finish and squared corners. Laxcon Steels draws it from 12.7 mm to 55 mm (1/2" to 2"), held to h11, k12 or k13, in lengths up to 6 metres.
Square Bright Bars are produced from hot-rolled bars through cold drawing and polishing processes. As a leading square bright bar manufacturer in India, we manufacture square bright bars with enhanced mechanical properties, greater dimensional accuracy, and subtle surface finish, and are free from surface defects. Our square bright bars’ quality makes them a preferred choice of various leading industries that demand high dimensional accuracy and perfection. SS square bar, stainless steel square bar, 316 square, and stainless steel solid square options are also widely available. These bars are known for their corrosion-resistant properties and exceptional tensile strength, making them ideal for industries.
Weight per metre by side length is in the square bar weight chart, and the weight calculator works it out for any size in the range.
Square Bar Specifications
- Size range
- 12.7 mm - 55 mm (1/2" - 2")
- Length
- Up to 6 metres
- Tolerance
- Size limits: h11, k12, k13, ASTM A484
- Grit polish
- On request
- Heat treatment
- Solution Annealed, Oil & Water Quenched / Tempered
- Bar ends
- Deburred Ends, Plain Ends without Burrs or Sharp Edges
- Standards
- ASTM A276, A484; EN 10088-3, EN 10278, EN 10059
- Contamination
- Free from radioactive elements, mercury and lead
- Testing
- PMI grade check with handheld spectrometers
- Weight per metre
- Weight table on this page
- Production
- Made to order in every grade listed on this page
- Certifications
- IATF 16949:2016, AS9100:2016 Rev. D, CE Marking
Sizes and Tolerances
Size Range
| Square drawn (mm) | Square drawn (in) | Drawn from black bar (mm) |
|---|---|---|
| 12.7 mm | 1/2" | 14 mm |
| 15 mm | 16 mm | |
| 15.88 mm | 5/8" | 17 mm |
| 19 mm | 20 mm | |
| 19.05 mm | 3/4" | 20 mm |
| 20 mm | 21.5 mm | |
| 22 mm | 23.5 mm | |
| 22.22 mm | 7/8" | 23.5 mm |
| 25 mm | 26.5 mm | |
| 25.4 mm | 1" | 27 mm |
| 26 mm | 27.5 mm | |
| 27 mm | 28.5 mm | |
| 28 mm | 30 mm | |
| 28.58 mm | 1-1/8" | 30 mm |
| 30 mm | 32 mm | |
| 31.75 mm | 1-1/4" | 34 mm |
| 32 mm | 34 mm | |
| 34 mm | 36 mm | |
| 35 mm | 37 mm | |
| 36 mm | 38 mm | |
| 38 mm | 40 mm | |
| 38.1 mm | 1-1/2" | 40 mm |
| 40 mm | 42 mm | |
| 41 mm | 43 mm | |
| 44 mm | 46 mm | |
| 45 mm | 47 mm | |
| 47 mm | 49 mm | |
| 48 mm | 50 mm | |
| 50 mm | 52 mm | |
| 50.8 mm | 2" | 53 mm |
| 55 mm | 57 mm |
Tolerance by size, ISO 286
| Nominal side (mm) | h11 | k12 | k13 |
|---|---|---|---|
| over 10 to 18 | 0 / -0.110 | 0 / +0.180 | 0 / +0.270 |
| over 18 to 30 | 0 / -0.130 | 0 / +0.210 | 0 / +0.330 |
| over 30 to 50 | 0 / -0.160 | 0 / +0.250 | 0 / +0.390 |
| over 50 to 80 | 0 / -0.190 | 0 / +0.300 | 0 / +0.460 |
Deviations in millimetres from the nominal size, ISO 286-1 and ISO 286-2.
Square Bar Grades
Austenitic
Square Bar Reference
Governing standards
- EN 10088-3
- Stainless steels: technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products for general purposes. Composition, heat treatment condition and mechanical properties per grade.
- EN 10278
- Dimensions and tolerances of bright steel products: the h and k tolerance classes for drawn, turned, peeled and ground bars.
- EN 10059
- Hot rolled square steel bars for general purposes: dimensions and tolerances on shape and dimensions.
- ASTM A276/A276M
- Stainless steel bars and shapes: composition, condition, mechanical properties and finish designations for hot-finished and cold-finished bar.
- ASTM A484/A484M
- General requirements for stainless steel bars, billets and forgings: permissible variations in dimensions, straightness, weight and length, and the test and marking requirements every bar order inherits.
- ISO 286-1 and 286-2
- The ISO code system for tolerances on linear sizes: the IT grades and the fundamental deviations behind h7, h9, h11, k12, k13, j6, f7 and f8.
- EN 10204
- Metallic products, types of inspection documents: the 2.2 test report and the 3.1 and 3.2 inspection certificates a purchase order can call for.
Weight per metre
| Side (mm) | kg per metre | Metres per tonne |
|---|---|---|
| 12.7 | 1.27 | 784.8 |
| 15 | 1.78 | 562.6 |
| 15.88 | 1.99 | 502.0 |
| 19 | 2.85 | 350.6 |
| 19.05 | 2.87 | 348.8 |
| 20 | 3.16 | 316.5 |
| 22 | 3.82 | 261.5 |
| 22.22 | 3.90 | 256.4 |
| 25 | 4.94 | 202.5 |
| 25.4 | 5.10 | 196.2 |
| 26 | 5.34 | 187.3 |
| 27 | 5.76 | 173.6 |
| 28 | 6.19 | 161.5 |
| 28.58 | 6.45 | 155.0 |
| 30 | 7.11 | 140.6 |
| 31.75 | 7.96 | 125.6 |
| 32 | 8.09 | 123.6 |
| 34 | 9.13 | 109.5 |
| 35 | 9.68 | 103.3 |
| 36 | 10.24 | 97.7 |
| 38 | 11.41 | 87.7 |
| 38.1 | 11.47 | 87.2 |
| 40 | 12.64 | 79.1 |
| 41 | 13.28 | 75.3 |
| 44 | 15.29 | 65.4 |
| 45 | 16.00 | 62.5 |
| 47 | 17.45 | 57.3 |
| 48 | 18.20 | 54.9 |
| 50 | 19.75 | 50.6 |
| 50.8 | 20.39 | 49.1 |
| 55 | 23.90 | 41.8 |
Density 7.90 g/cm³, plain section (side squared x 0.0079).
Square bright bar against square black bar
Each drawn square size on this page is produced from the black (hot rolled) square listed beside it in the size table: the draw reduces the section by roughly 1 to 2 mm on the side and squares the corners, and the tolerance goes from the hot rolled allowance of EN 10059 to h11 under EN 10278. A part that is machined on all four faces is cut from the black bar; a part that keeps one or more faces as supplied, such as a key, a guide or an architectural section, is cut from the drawn bar.
Weight per metre is side squared times 0.0079, so a 40 mm square weighs 12.6 kg per metre, 27 percent more than a 40 mm round of the same grade. The round cornered square is the hot rolled forging-quality section, in sizes from 45 to 100 mm.
Frequently Asked Questions
What stainless steel square bar sizes does Laxcon make?
Laxcon draws stainless steel square bright bars from 12.7 mm to 55 mm, in lengths up to 6 metres. The size table above lists each drawn size beside the black size it is drawn from.
Which tolerances and heat treatments are available for square bars?
Stainless steel square bars can be supplied to h11, k12, k13 or ASTM A484 tolerances in solution-annealed, oil-quenched, water-quenched or tempered condition.
Which square-bar end and surface finishes are available?
Square bar ends can be deburred or supplied plain without sharp edges, and grit polishing is available to the customer's stated requirement. Grade confirmation is available through handheld PMI.
How can stainless steel square bright bars be packed and traced?
Laxcon packs stainless steel square bright bars in standard bundles of 500 to 1,000 kg with HDPE or LDPE wrapping and two lifting slings. ISPM 15 wooden boxes and fibre-tube packing are available, and every bundle is marked with heat number, grade, size, and net and gross weight.
What is the weight of a 20 mm square bar per metre?
A 20 mm stainless steel square bar weighs 3.16 kg per metre at 7.90 g/cm³, so one tonne holds about 316 metres of bar. Weight per metre is the side in millimetres squared times 0.0079.
Which grades are stainless steel square bars made in?
Laxcon makes square bright bars in the austenitic, martensitic and ferritic, duplex and precipitation hardening stainless steels and in carbon and alloy steels, every grade listed on this page. The 304 and SAE 4140 square bars each have their own page.
What is the price of a stainless steel square bar?
Stainless steel square bar is priced per kilogram, and the price depends on the grade, the size, the tolerance class, the finish, the length and the quantity ordered. Laxcon Steels quotes each order on request; what moves the price of stainless steel in general is set out in the stainless steel price article.
More questions
What is the weight of a 12 mm square bar per metre?
A 12 mm stainless steel square bar weighs about 1.14 kg per metre (12 x 12 x 0.0079). The smallest drawn square Laxcon makes is 12.7 mm (1/2"), which weighs 1.27 kg per metre.
What does h11 tolerance mean on a 25 mm square bar?
Under ISO 286, h11 allows a 25 mm square bar to measure 24.870 to 25.000 mm across the side, never oversize. The k12 class allows 25.000 to 25.210 mm and k13 allows 25.000 to 25.330 mm, never undersize. The tolerance table above gives each class for every size band.
How does Laxcon make square bright bars?
Laxcon produces square bright bars from hot rolled black squares by cold drawing and polishing. The draw reduces the side by about 1 to 2 mm and squares the corners, so each drawn size comes from the black size listed beside it, such as 40 mm drawn from 42 mm.
What is a stainless steel square bright bar used for?
A square bright bar is used where a part keeps one or more of its faces as supplied, such as a key, a guide or an architectural section. A part machined on all four faces is cut from the black square instead.
How much heavier is a square bar than a round bar of the same size?
A square bar weighs about 27 percent more than a round bar of the same size and grade. A 40 mm square weighs 12.64 kg per metre.
Which company manufactures stainless steel square bright bars in India?
Laxcon Steels manufactures stainless steel square bright bars in Gujarat, India, from 12.7 mm to 55 mm in lengths up to 6 metres. It melts the steel in its own melting shop, rolls it into bar and cold finishes the bar in its own plants.
What is a square bright bar?
A square bright bar is a hot rolled square bar cold drawn to a close tolerance with a clean surface, and the bright bar vs black bar article compares it with the hot rolled bar.
CATALOGUE
More
Products
Bright Bars
Precision Shaft Quality (PSQ) Bars
Pipes and Tubes
Hexagonal Bright Bars
Cold-Drawn Flat Bars
Forged & Proof Machined Bars
HRAP Flat Bars
HRAP Equal Angles
HRAP Unequal Angles
Threaded Bars
Hot Rolled Round Cornered Squares (RCS) Bars
Hot Rolled Round Bars
Continuous Cast Billets / Blooms
Channels
Forging Quality Ingots
Precipitation Hardening Steels
Duplex Steel
T-Profile